良好的維護與保養能保證機組可靠運行。正常使用情況下，合金尾氣發電機組的保養工作應按規定的日保養、周保養、月保養要求進行。通過這些規定的保養，能及時發現機組是否存在聲音異常、動作異常、外觀異常、溫度異常、壓力異常和氣味異常等故障現象，從而及時對機組進行檢查和調整，進而有針對性的加以解決,確保機組正常運行。

　　Good maintenance and upkeep can ensure the reliable operation of the unit. Under normal use, the maintenance of the alloy exhaust gas generator set should be carried out according to the prescribed daily, weekly, and monthly maintenance requirements. Through these prescribed maintenance procedures, it is possible to promptly detect any abnormal sounds, movements, appearances, temperatures, pressures, odors, or other malfunctions in the unit. This enables timely inspection and adjustment of the unit, and targeted solutions to ensure its normal operation.

　　在這些保養要求中，要特別注意以下三個方面的檢查和保養：

　　Among these maintenance requirements, special attention should be paid to the following three aspects of inspection and maintenance:

　　(1) 潤滑系統的檢查和保養。

　　(1) Inspection and maintenance of lubrication system.

　　該機組由于存在運轉部件多，運轉部件工作條件惡劣，大多處在高溫、高沖擊載荷狀態下，需要潤滑的部位較多，對潤滑系統的可靠性要求較為苛刻，因此要注意檢查潤滑油系統的油質情況、油位情況、油溫和油壓情況,注意離心濾清器和機油濾清器的清洗，避免出現因潤滑不良造成的機組零部件磨損加劇，縮短機組零部件的使用壽命。

　　Due to the numerous operating components and harsh working conditions of the unit, most of which are under high temperature and high impact loads, there are many parts that require lubrication, and the reliability requirements for the lubrication system are quite strict. Therefore, attention should be paid to checking the oil quality, oil level, oil temperature, and oil pressure of the lubrication system, and cleaning the centrifugal filter and oil filter to avoid increased wear of the unit components caused by poor lubrication and shorten the service life of the unit components.

　　(2) 空氣過濾器的檢查和保養。

　　(2) Inspection and maintenance of air filters.

　　空氣過濾器如果運轉良好的話，將有效地避免因進氣阻力大引起的增壓壓力下降過大，進而造成渦輪增壓器出現漏油現象；還可避免因流量減少引起的渦輪增壓器壓氣機喘振現象。因此要定期清理空氣過濾器，必要時更換新濾芯。在潮濕地區可將紙質濾芯抽掉。

　　If the air filter operates well, it will effectively prevent excessive pressure drop caused by high intake resistance, which can lead to oil leakage in the turbocharger; It can also avoid the phenomenon of turbocharger compressor surge caused by reduced flow. Therefore, it is necessary to regularly clean the air filter and replace the filter element if necessary. In humid areas, the paper filter can be removed.

　　(3) 相關間隙和角度的檢查和調整。主要是火花塞間隙、氣門間隙和配氣定時等的檢查和調整。

　　(3) Inspection and adjustment of relevant gaps and angles. Mainly the inspection and adjustment of spark plug clearance, valve clearance, and valve timing.

　　合金尾氣發電機組運行一段時間后，火花塞的間隙會有所變大，這是正常現象。若間隙增大到0.89mm時，火花塞將出現失火現象，造成機組運行不穩，甚至停車，所以應定期檢查和調整，同時消除火花塞及其螺紋處出現的積炭,確保其好用。

　　After running the alloy tail gas generator set for a period of time, the gap between the spark plugs will increase, which is a normal phenomenon. If the gap increases to 0.89mm, the spark plug will ignite, causing unstable operation and even shutdown of the unit. Therefore, regular inspection and adjustment should be carried out, and the carbon deposits at the spark plug and its threads should be eliminated to ensure its usability.

　　另外，合金尾氣發電機組經長時間運轉后，由于配氣機構的磨損和松動等原因，會引起氣門間隙的變化,應定期檢查并調整氣門間隙。配氣定時在正常情況下不需要進行調整，當機組各缸工作狀態出現異常時，應首先檢查指針上止點指示位置是否正確，檢查傳動系統各齒輪傳動記號是否對準，整個系統的裝配關系及氣門間隙是否正確。若經檢查調整后，仍與規定值差異較大時，則應考慮凸輪軸或齒輪傳動件有無損壞現象，必要時進行修復或更換。

　　In addition, after long-term operation, the alloy exhaust gas generator set may experience changes in valve clearance due to wear and looseness of the valve mechanism, and the valve clearance should be regularly checked and adjusted. Under normal circumstances, the valve timing does not need to be adjusted. When the working status of each cylinder in the unit is abnormal, the first thing to check is whether the pointer's top dead center indication position is correct, whether the transmission marks of each gear in the transmission system are aligned, and whether the assembly relationship and valve clearance of the entire system are correct. If there is still a significant difference from the specified value after inspection and adjustment, the camshaft or gear transmission components should be considered for damage and repaired or replaced if necessary.

　　本文由   合金尾氣發電機組 友情奉獻.更多有關的知識請點擊  http://www.hfdxyy.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the alloy tail gas generator set For more related knowledge, please click http://www.hfdxyy.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.